本帖最后由 八云紅 于 2025-9-11 09:52 編輯
TTL跑碼：信息如下：請教各位大佬 這是CM311-1a的CPU壞了，還是機身內存壞了，需要怎么解決，請指導！
bl2_stage_init 0x02
L0:00000000
L1:00000703
L2:00008267
L3:04000000
S1:00000000
B2:00002000
B1:e0f83180
TE: 229596
BL2 Built : 14:02:05, Nov 23 2020. g12a g966c864 - gongwei.chen@droid11-sz
Board ID = 8
Set cpu clk to 24M
Set clk81 to 24M
CPU clk: 1200 MHz
Set clk81 to 166.6M
eMMC boot @ 0
sw8 s
board id: 8
Load FIP HDR DDR from eMMC, src: 0x00010200, des: 0xfffd0000, size: 0x00004000, part: 0
fw parse done
PIEI prepare done
00000000
emmc switch 1 ok
ddr saved addr:00016000
Load ddr parameter from eMMC, src: 0x02c00000, des: 0xfffd0000, size: 0x00001000, part: 0
00000000
emmc switch 0 ok
fastboot data verify
result: 255
Cfg max: 12, cur: 1. Board id: 255. Force loop cfg
LPDDR4 probe
LPDDR4_PHY_V_0_1_22-Built : 15:59:30, May 25 2020. g12a gb6bfa83 - gongwei.chen@droid11-sz
ddr clk to 1176MHz
dmc_version 0000
Check phy result
INFO : End of CA training
INFO : End of initialization
INFO : Training has run successfully!
Check phy result
INFO : End of initialization
INFO : End of read enable training
INFO : End of fine write leveling
INFO : End of read dq deskew training
INFO : End of MPR read delay center optimization
INFO : End of Write leveling coarse delay
INFO : End of read delay center optimization
INFO : Training has run successfully!
Check phy result
INFO : End of initialization
INFO : End of MPR read delay center optimization
INFO : End of write delay center optimization
INFO : End of read delay center optimization
INFO : End of max read latency training
INFO : Training has run successfully!
1D training succeed
Check phy result
INFO : End of initialization
INFO : End of 2D read delay Voltage center optimization
INFO : End of 2D read delay Voltage center optimization
INFO : End of 2D write delay Voltage center optimization
INFO : End of 2D write delay Voltage center optimization
INFO : Training has run successfully!
soc_VRef_reg_value 0x 00000021 00000022 00000023 00000020 00000021 0000001f 00000020 00000020 00000022 00000022 00000020 00000022 00000020 00000021 0000001f 0000001f 00000023 00000021 00000021 00000020 00000020 00000022 00000023 00000023 00000021 00000022 00000023 00000023 0000001f 00000023 00000024 00000023 dwc_ddrphy_apb_wr((0<<20)|(2<<16)|(0<<12)|(0xb0):0004
dram_vref_reg_value 0x 00000060
2D training succeed
auto size-- 65535DDR cs0 size: 1024MB
DDR cs1 size: 1024MB
DMC_DDR_CTRL: 00e0001bDDR size: 2048MB
cs0 DataBus test pass
cs1 DataBus test pass
cs0 AddrBus test pass
cs1 AddrBus test pass
non-sec scramble use zero key
ddr scramble enabled
100bdlr_step_size ps== 452
result report
boot times 0Enable ddr reg access
00000000
emmc switch 3 ok
Authentication key not yet programmed
get rpmb counter error 0x00000007
00000000
emmc switch 0 ok
Load FIP HDR from eMMC, src: 0x00010200, des: 0x01700000, size: 0x00004000, part: 0
Load BL3X from eMMC, src: 0x00078200, des: 0x01768000, size: 0x000dac00, part: 0
0.0;M3 CHK:0;cm4_sp_mode 0
[Image: g12a_v1.1.3394-7d43064d5 2020-05-07 15:37:06 gongwei.chen@droid11-sz]
OPS=0x70
ring efuse init
28 0c 70 00 01 2d 05 00 00 0f 33 39 33 4e 48 50
[0.014271 Inits done]
secure task start!
high task start!
low task start!
boot bl31
NOTICE: BL31: v1.3(release):079690f10
NOTICE: BL31: Built : 16:11:33, Nov 8 2021
NOTICE: BL31: G12A normal boot!
NOTICE: BL31: BL33 decompress pass
ERROR: Error initializing runtime service opteed_fast
U-Boot 2015.01 (Dec 30 2021 - 18:08:05)
DRAM: 2 GiB
Relocation Offset is: 76e3b000
mmu cfg end: 0x80000000
mmu cfg end: 0x80000000
spi_post_bind(spifc): req_seq = 0
register usb cfg[0][1] = 0000000077f387e8
NAND: get_sys_clk_rate_mtd() 292, clock setting 200!
bus cycle0: 6,timing: 7
NAND device id: 0 ff ff ff ff ff
No NAND device found!!!
nand init failed: -6
get_sys_clk_rate_mtd() 292, clock setting 200!
bus cycle0: 6,timing: 7
NAND device id: 0 ff ff ff ff ff
No NAND device found!!!
nand init failed: -6
MMC: aml_priv->desc_buf = 0x0000000073e2bd90
aml_priv->desc_buf = 0x0000000073e2e0d0
SDIO Port B: 0, SDIO Port C: 1
co-phase 0x2, tx-dly 0, clock 400000
co-phase 0x2, tx-dly 0, clock 400000
co-phase 0x2, tx-dly 0, clock 400000
emmc/sd response timeout, cmd8, cmd->cmdarg=0x1aa, status=0x1ff2800
emmc/sd response timeout, cmd55, cmd->cmdarg=0x0, status=0x1ff2800
co-phase 0x2, tx-dly 0, clock 400000
co-phase 0x2, tx-dly 0, clock 40000000
[set_emmc_calc_fixed_adj][875]find fixed adj_delay=20
init_part() 297: PART_TYPE_AML
[mmc_init] mmc init success
Amlogic multi-dtb tool
GZIP format, decompress...
Multi dtb detected
Multi dtb tool version: v2 .
Support 3 dtbs.
aml_dt soc: g12a platform: u212 variant: 2g
dtb 0 soc: g12a plat: u212 vari: 1g
dtb 1 soc: g12a plat: u212 vari: 2g
dtb 2 soc: sm1 plat: ac213 vari: 2g
Find match dtb: 1
start dts,buffer=0000000073e30920,dt_addr=0000000073e30920
get_partition_from_dts() 92: ret 0
Amlogic multi-dtb tool
Single dtb detected
parts: 18
00: logo 0000000000800000 1
01: recovery 0000000001800000 1
02: misc 0000000000800000 1
03: dtbo 0000000000800000 1
04: cri_data 0000000000800000 2
05: param 0000000001000000 2
06: boot 0000000001000000 1
set has_boot_slot = 0
07: rsv 0000000001000000 1
08: metadata 0000000001000000 1
09: vbmeta 0000000000200000 1
10: tee 0000000002000000 1
11: vendor 0000000014000000 1
12: odm 0000000008000000 1
13: system 0000000050000000 1
14: product 0000000008000000 1
15: cache 0000000040000000 2
16: backup 0000000040000000 2
17: data ffffffffffffffff 4
init_part() 297: PART_TYPE_AML
eMMC/TSD partition table have been checked OK!
crc32_s:0x1577dad == storage crc_pattern:0x1577dad!!!
crc32_s:0xee152b83 == storage crc_pattern:0xee152b83!!!
crc32_s:0x79f50f07 == storage crc_pattern:0x79f50f07!!!
mmc env offset: 0x47400000
In: serial
Out: serial
Err: serial
board_late_init: boardid = 0x8
aml log : internal sys error!
reboot_mode=cold_boot
[store]To run cmd[emmc dtb_read 0x1000000 0x40000]
_verify_dtb_checksum()-3476: calc 9002a8b7, store 9002a8b7
_verify_dtb_checksum()-3476: calc 9002a8b7, store 9002a8b7
dtb_read()-3691: total valid 2
update_old_dtb()-3672: do nothing
Amlogic multi-dtb tool
GZIP format, decompress...
Multi dtb detected
Multi dtb tool version: v2 .
Support 3 dtbs.
aml_dt soc: g12a platform: u212 variant: 2g
dtb 0 soc: g12a plat: u212 vari: 1g
dtb 1 soc: g12a plat: u212 vari: 2g
dtb 2 soc: sm1 plat: ac213 vari: 2g
Find match dtb: 1
amlkey_init() enter!
[EFUSE_MSG]keynum is 4
vpu: driver version: v20190313
vpu: detect chip type: 8
vpu: clk_level default: 7(666667000Hz), max: 7(666667000Hz)
vpu: clk_level in dts: 7
vpu: vpu_power_on
vpu: set_vpu_clk
vpu: set clk: 666667000Hz, readback: 666666667Hz(0x100)
vpu: set_vpu_clk finish
vpu: vpu_module_init_config
vpp: vpp_init
vpp: vpp osd2 matrix rgb2yuv..............
hdr_func 4, hdr_process_select 0x1
cvbs: cpuid:0x28
vdac_gsw_init: 0x0
cvbs: find clk_path: 0x0
cvbs: find performance_pal config
cvbs: find performance_ntsc config
hpd_state=0
do_hpd_detect: hdmimode=1080p60hz
do_hpd_detect: colorattribute=444,8bit
Saving Environment to aml-storage...
mmc env offset: 0x47400000
Writing to MMC(1)... done
aml_config_dtb 633
aml_config_dtb 663
co_phase = <0x00000003>
caps2 = "MMC_CAP2_HS200"
f_max = "
??"
status = "disabled"
status = "okay"
Net: dwmac.ff3f0000amlkey_init() enter!
amlkey_init() 71: already init!
[EFUSE_MSG]keynum is 4
wipe_data=successful
wipe_cache=successful
upgrade_step=2
aml log : internal sys error!
reboot_mode:::: cold_boot
ext4logoLoadCmd=ext4load mmc 1:${logoPart} ${logoLoadAddr} ${ext4LogoPath}
6220854 bytes read in 173 ms (34.3 MiB/s)
[imgread]load bmp from ext4 part okay
bmp pixel: 24
[OSD]load fb addr from dts:/meson-fb
[OSD]set initrd_high: 0x7f800000
[OSD]fb_addr for logo: 0x7f800000
[OSD]load fb addr from dts:/meson-fb
[OSD]fb_addr for logo: 0x7f800000
[OSD]VPP_OFIFO_SIZE:0xfff01fff
[CANVAS]canvas init
[CANVAS]addr=0x7f800000 width=5760, height=2160
[OSD]osd_hw.free_dst_data: 0,719,0,575
[OSD]osd1_update_disp_freescale_enable
vpp: vpp_matrix_update: 2
cvbs_performance_enhancement
cvbs_config_hdmipll_g12a
cvbs_set_vid2_clk
vdac_enable: 1, module_sel:0x8
hdr_packet
vpp: hdr_policy = 1
vpp: Rx hdr_info.hdr_sup_eotf_smpte_st_2084 = 0
amlkey_init() enter!
amlkey_init() 71: already init!
[EFUSE_MSG]keynum is 4
[KM]Error:f[key_manage_query_size]L515:key[oemkey] not programed yet
Command: bcb uboot-command
Start read misc partition datas!
BCB hasn't any datas,exit!
time_out = 7a120
key[0] = b8471420
key[1] = b847ff00
key[2] = 6699dd22
key[3] = 66994cb3
irkey - irkey <timeout> <key1> ...<keyN> - maximum value of N: 10
Usage:
irkey - No additional help available.
amlkey_init() enter!
amlkey_init() 71: already init!
[EFUSE_MSG]keynum is 4
[KM]Error:f[key_manage_query_size]L515:key[oemkey] not programed yet
Hit Enter or space or Ctrl+C key to stop autoboot -- : 0
pll tsensor avg: 0x20ac, u_efuse: 0x80ba
temp1: 41
ddr tsensor avg: 0x2091, u_efuse: 0x806a
temp2: 42
device cool done
CONFIG_SYSTEM_AS_ROOT: null
system_mode: 0
Start read misc partition datas!
info->magic =
info->version_major = 1
info->version_minor = 0
info->slots[0].priority = 15
info->slots[0].tries_remaining = 7
info->slots[0].successful_boot = 0
info->slots[1].priority = 14
info->slots[1].tries_remaining = 7
info->slots[1].successful_boot = 0
info->crc32 = -1075449479
active slot = 0
CONFIG_AVB2: null
active_slot: normal
avb2: 0
ee_gate_off ...
avb2: 0
## Booting Android Image at 0x01080000 ...
Kernel command line: androidboot.dtbo_idx=0 buildvariant=userdebug
[store]Is good fdt check header, no need decrypt!
active_slot is normal
load dtb from 0x1000000 ......
Amlogic multi-dtb tool
Single dtb detected
find 1 dtbos
dtbos to be applied: 0
Apply dtbo 0
Loading Kernel Image(COMP_NONE) ... OK
kernel loaded at 0x01080000, end = 0x01a09350
Loading Ramdisk to 09e93000, end 09fff0ad ... OK
Loading Device Tree to 0000000009e7b000, end 0000000009e923d6 ... OK
fdt_fixup_memory_banks, reg:0000000000000000
Starting kernel ...
uboot time: 3323464 us
|
網站導航
發表于 2025-9-10 20:29
收藏
淘帖
頂一個
踩
提升卡
置頂卡
變色卡
千斤頂
樓主
/1 
znds.com 