ゝ．慌 發表于 2015-5-26 14:12
看論壇置頂教程啊

GND RX TX怎么看呢？我是100E

樓里的各位大神，包括樓主，能把spi的固件備份一份發給我不，我的天貓魔盒tmb100c也掛了，沒ttl接口，要燒錄，沒固件，希望備份一份

學習學習！

請教大拿；TMB100E怎么和電腦鏈接圖，下載的recovery.img壓縮包無法解壓怎么刷機，

TMB100E怎么和電腦鏈接，下載的recovery.img壓縮包無法解壓怎么刷機，

SkyFire 發表于 2015-5-29 21:37
估計是Data分區變只讀了，焊下spi flash，上編程器重刷入UBOOT，再接TTL查看是否有壞塊，刷Data分區修復 ...

我覺得你說的對，我的魔盒突然出現存儲空間為0，然后就卡logo了。以后買個編程器試試。

18994992234 發表于 2015-5-29 21:15
刷的樂視，一直好好的，突然掛了

估計是Data分區變只讀了，焊下spi flash，上編程器重刷入UBOOT，再接TTL查看是否有壞塊，刷Data分區修復包，不行只能換NAND Flash。

SkyFire 發表于 2015-5-29 20:51
之前刷什么固件。

刷的樂視，一直好好的，突然掛了

18994992234 發表于 2015-5-27 18:43
EEEE I3000000032940xf300110003877520EEEE I400000004294_M6_BL1_3431>2534313
device is 16bit ddr
wait  ...

之前刷什么固件。

EEEE I3000000032940xf300110003877520EEEE I400000004294_M6_BL1_3431>2534313
device is 16bit ddr
wait pll-0x03 target is 0204 now it is 0x00000203

DDR clock is 516MHz with 1T mode

516M clk
DX0DLLCR:40000000
DX0DQTR:ffffffff
DX0DQSTR:3db05001
DX1DLLCR:40000000
DX1DQTR:ffffffff
DX1DQSTR:3db05001
DX2DLLCR:40000000
DX2DQTR:ffffffff
DX2DQSTR:3db05001
DX3DLLCR:40000000
DX3DQTR:ffffffff
DX3DQSTR:3db04001
Stage 00 Result 00000000
Stage 01 Result 00000000
Stage 02 Result 00000000
Stage 03 Result 00000000
HHH
Boot From SPI0x12345678
Boot from internal device 1st SPI RESERVED

System Started
?nv_init env_init 40


U-boot-00000-g3e9c579(m6_mbx_g32@jb42-0630) (Apr 08 2014 - 12:22:39)

aml_rtc_init
aml rtc init first time!
Clear HDMI KSV RAM
DRAM:  1 GiB
relocation Offset is: 105e8000
NAND:  Amlogic nand flash uboot driver, Version U1.06.017 (c) 2010 Amlogic Inc.
SPI BOOT : continue i 0
No NAND device found!!!
NAND device id: 2c 68 4 4a a9 0
NAND device: Manufacturer ID: 0x2c, Chip ID: 0x2c (Micron C revision NAND 4GiB MT29F32G-C)
1 NAND chips detected
#####aml_nand_init, with RB pins and chip->chip_delay:20
bus_cycle=5, bus_timing=6, start_cycle=6, end_cycle=7,system=5.0ns
oob size is not enough for selected bch mode: NAND_BCH60_1K_MODE force bch to mode: NAND_BCH30_1K_MODE
aml_chip->oob_fill_cnt =0,aml_chip->oob_size =224,bch_bytes =54
aml_nand_init:oobmul =2,chip->ecc.layout->oobfree[0].length=16,aml_chip->oob_size=224
aml nand env valid addr: 10000 ,status =0
key start_blk=2040,end_blk=2047,aml_nand_key_init:684
aml nand key valid addr: ff010000
aml nand key valid addr: ff210000
aml nand key valid addr: ff410000
aml nand key valid addr: ff610000
CONFIG_KEYSIZE=0x10000; KEYSIZE=0xfffc; bbt=0x1330; default_keyironment_size=0xeccc
i=0,register --- nand_key
NAND bbt detect factory Bad block at 5a00000
Creating 8 MTD partitions on "nandnormal":
0x000000800000-0x000001000000 : "logo"
0x000001000000-0x000001800000 : "aml_logo"
0x000001800000-0x000002000000 : "recovery"
0x000002000000-0x000002800000 : "boot"
0x000002800000-0x000042a00000 : "system"
NAND bbt detect factory Bad block at 5a00000
0x000042a00000-0x000062a00000 : "cache"
0x000062a00000-0x000072a00000 : "backup"
0x000072a00000-0x0000ff000000 : "data"
nandnormal initialized ok
detect mx chiprevD :1 and nand_type: 0
nand_curr_device =1
MMC:   SDIO Port B: 0, SDIO Port C: 1
SPI BOOT,spi_env_relocate_spec : env_relocate_spec 53

do not to enable write protect for S25FL032A!!!
In:    serial
Out:   serial
Err:   serial
register usb cfg[0] = 9fe82948
Net:   current factory:3
default eth phy
Meson_Ethernet
init suspend firmware done. (ret:0)
detect_storage
nand exist return 0
setenv storage nand
reboot_mode=charging
ir init
switch_boot_mode
suspend_status_current2=0
current factory:3
Hit Enter key to stop autoboot:  0
compatible nand
Booting from nand ...

NAND read: logo whole chip
8388608 bytes read: OK

NAND read: boot offset 0x0, size 0x600000
6291456 bytes read: OK
pre-clear hdmi ram
hdcp get form storage medium: nand
name=nand_key nand_key
read:addr:0xff010000,phy_blk_addr:2040,phy_page_addr:8,aml_nand_get_key:125
device:nand, init key ok!!
don't found keyname,uboot_key_read:1502
prefetch hdcp keys from nand failed
## Booting kernel from Legacy Image at 82000000 ...
   Image Name:   Linux-3.0.50-gba996df
   Image Type:   ARM Linux Kernel Image (lzma compressed)
   Data Size:    3407353 Bytes = 3.2 MiB
   Load Address: 80008000
   Entry Point:  80008000
   Verifying Checksum ... OK
        Ramdisk start addr = 0x82340800, len = 0x1011bb
   Uncompressing Kernel Image ... OK
machid from environment: 0x4e27
EFUSE machid is not set.
Using machid 0x4e27 from environment

Starting kernel ...

[    4.545216@0] kobject (df8b9410): tried to init an initialized object, something is seriously wrong.
[    4.564757@0] dvb_io_setup start
[    4.568861@0] DVB: cannot get resource "frontend0_LNBON/OFF"
[    4.568892@0] DVB: cannot get resource "frontend0_POWERON/OFF"
[    4.574755@0] DVB: cannot get resource "frontend0_ANTOVERLOAD"
[    4.581279@0] Smartcard: cannot get resource "smc0_reset"
[    4.974041@0] init: hdmi hpd_status is :48
[    4.983585@0] init: cannot open '/initlogo.rle'
[    4.983790@0] init: load_565rle_image_mbx result is: 0
[    5.306168@0] init: Before e2fsck_main...

18994992234 發表于 2015-5-26 19:42
putty可以顯示，但是無法輸入命令

線接對了。
聽說要先中斷，又有說法某個版本的uboot不能中斷。
我也是不能輸入命令，搞不定，扔那里了。